FLIGHT CONTROLLER F722-STD

Share and Likes
  • 2
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
    2
    Shares

STM32F722RET6, ICM20602, BMP280, BFOSD, SD Card Slot, VCP+5x UARTs, 6x PWM / DShot outputs

F722-STD_layout

  • MCU: 216MHz STM32F722RET6
  • IMU: 32K ICM20602 gyro/accelerometer (SPI)
  • Baro: BMP280 (I2C)
  • OSD: BetaFlight OSD w/ AT7456E chip
  • Blackbox: MicroSD card slot (SD/SDHC)
  • VCP, UART1, UART2, UART3, UART4, UART5
  • PPM/UART Shared: UART2-RX
  • Battery Voltage Sensor: 1:10
  • Current Sensor: No (FCHUB-6S, FCHUB-VTX option)
  • BEC 5V: No (FCHUB-6S, FCHUB-VTX option)
  • LDO 3.3V: Max.300mA
  • I2C1 SDA & SCL: Yes
  • Camera control: Yes
  • DAC: Yes
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 7x PWM / DShot outputs without conflict
  • 5x UARTs
  • 1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 1x I2C1
  • 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
  • 1x Side-press button for BOOT(DFU) mode
  • 1x 16pin bottom mounted FFC Slot for FCHUB-6S or FCHUB-VTX connection
  • 36x36mm PCB with 30.5mm mounting holes
  • w/ 2x 0.5mm*16Pin 5cm Flexible Flat Cable
  • w/ 4pcs M3 Anti-vibration Standoffs

 

  1.  Album dan info
  2. Spec and feature
  3. Connection Guide
  4. Pin Inav & BF
  5. Firmware Download

TIPS

  • F7 32K loop can’t be supported now. Max. 32K/8K or 16k/16K with current BF3.2.3,  Max.32K/16K with last 3.3 build.
  • CLI “defaults” after reflashing
  • Rubber anti-vibration standoffs are necessary to avoid the vibration woes.
  • Put a piece of sponge on the barometer to reduce the impact of airflow.
  • If you are using 5V VTX, Pls power the VTX via the 5V pad on FCHUB.  The ribbon cable can’t bear heavy current.
  • SBUS, DSM, IBUS, SUMD can be connected to any unused UART_RX.
  • PPM share RX2 pad
  • Frsky SmartPort, Tramp & smartaudio protocol can be connected to any unused UART_TX
  • S6 pad (PA8) can be resourced to Camera Control
  • pwm pad (PB8) can be resourced to Camera Control, LED_STRIP, or Motor
  • SD Card, FAT32  C10, 1~32G,  But max.4G space can be used in Blackbox.

Buy  : Tokoheli


Share and Likes
  • 2
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
    2
    Shares

Related posts